Oil Cooler Connections – GM Quick Connects

In our first two tech tip articles we reviewed radiator cap functions and application considerations.  The next few articles will cover the different types of “Quick Connects” used by original equipment manufacturers to attach transmission and engine oil cooler lines to the heat exchangers in the power train cooling system.  In this particular article we will review the Jiffy-Tite® connector design which General Motors engineers started to use in some applications in 1996.  Most GM vehicles use Jiffy-Tite® connectors today, the exception being some of the Cadillac platforms.

Until the middle 90’s most oil coolers were connected to the oil lines using rubber hose and clamp or inverted flare joint designs.  See photo of rubber hose type connection and sketch of inverted flare joint below.

Rubber hose and clamp fitting  

Inverted flare connetion 


Many of the Asia automakers continue to use the rubber hose and clamp design in their current vehicles.  Each of these conventional joint designs has their own merits and disadvantages.  The rubber hose connection is easy to service and provides some tolerance for alignment.  One disadvantage is that sealing is affected by changes in clamping force as the rubber hardness varies with temperature and takes a compression set with age.

Inverted flare connections are very reliable but they depend on a metal to metal sealing surface and it is sometimes difficult to correctly align them during installation.  To seal effectively, one or both sides of the joint surface must be forced to conform to the other as the joint is tightened.  As parts become contaminated with corrosion and dirt it becomes even more difficult to effect leak proof connections. 

In many applications, steel lines and fittings are being jointed to brass or aluminum oil coolers.  When leaks occur at these joints the first repair attempt often results in over-tightening and stripping of the threads on the oil cooler connector.  Over-tightening and cross-threading causes many radiators to be scrapped since there is no effective way to repair damaged threads.  Over-tightening can also cause damage to the oil cooler inside the radiator tank where a leak will lead to mixing of oil and coolant.

Some aftermarket suppliers supply small o-rings to place in the interface between the male and female connections.  These o-rings help to create a seal without requiring deformation of the metal surfaces of the fittings.  See sketch below.

Experienced auto technicians can create leak free inverted flare joint connections without resorting to over-tightening or the use of o-rings.  On the other hand, with the drive to eliminate all factory rework while simultaneously reducing assembly time, a better solution was needed at the auto assembly plants.  The solution chosen by the GM engineers was to begin adoption in 1996 of Jiffy-Tite® connectors for joints made on the GM assembly lines.  Except for a few applications which use radiators and oil coolers produced by Denso, the Jiffy-Tite® connector has become a standard in GM applications and is also used in many Mercedes, Chrysler, and other applications.

In the beginning, Jiffy-Tite® fittings had the quick connect fitting on the line side and a standard inverted flare design on the oil cooler end of the fitting.  Subsequent designs use o-ring or seal washer designs on the oil cooler side.  See photos below.

In many later model radiator applications an integrated Jiffy-Tite® design is used to not only make the connection between the oil cooler and the line but also to secure the oil cooler in the radiator tank.  It is these later designs that prove most troublesome in the field.  These fittings are not intended to be disturbed once the radiator leaves the factory.  Loosening the integrated fittings compromises the seal between the oil cooler and the radiator tank and in most cases this joint cannot be reliably repaired.  See photos below.


To remove the oil line from a Jiffy-Tite® connector first slide back the plastic cover (if present) and then use the appropriate tool to open the legs of the retaining clips.  Once the legs are open the line may be pulled out of the fitting.  If a tool is not available to open the legs then a small screwdriver can be used to completely remove the clip from the fitting.  See photos below.

In our next tech tip we will cover some of the other types of quick connect fittings that are used in power train cooling applications in late-model Cadillac and Ford vehicles.

Post a comment or leave a trackback: Trackback URL.


  • Jamboree In The Hills  On February 16, 2011 at 4:43 pm

    Awesome post. Do you mind if I ask what your source is for this information?

    • Marv Beasley  On February 23, 2011 at 9:16 am

      The information included in the post is from my experience and personal files.

  • al hamner  On June 4, 2011 at 10:04 am

    Once a jiffy tite trans cooler connection fails what is the fix

    • Marv Beasley  On June 5, 2011 at 11:22 am

      Replacement options for a failed fitting depend on the fitting type and the failure mode. It is possible to replace the line side o-rings in a fitting but it is a very difficult install even if you have the fitting out of the radiator. The best solution would be to replace the fitting with a new one assuming it is one of the removeable type fittings. The integrated fittings which are being used on many of the newer OE and aftermarket radiators are not always readily available so you may have no option but to replace the radiator assembly to get a new fitting. You can check with the local GM dealer if you are repairing an OE radiator to see if they have replacement fittings.

  • Kenneth Machala  On March 2, 2013 at 5:44 pm

    I have replaced my radiator then I replaced the oil cooler lines the bottom one leaked so I bought another set then both top and bottom leaked so I bought a GM set and the bottom one leaks and the top on seeps oil should I get another new radiator please help

    • Marv Beasley  On March 3, 2013 at 8:47 pm

      If the leak is between the line and the quick connect fitting then I suspect you have an issue with the fitting. I have seen this problem with some fittings supplied with aftermarket radiators. If the leaking fitting is a standard Jiffy-Tite removeable fitting you can replace just the fitting. If it is the integrated type then you may have to replace the radiator. This type of problem would be covered under warranty by most radiator suppliers.

  • Verona Henry  On April 30, 2022 at 11:01 pm

    Question own a c 6 Corvette 2007 radiator comes with 2 oil coolers 1 inside each plastic tank the driver side tank has larger fittings for quick connections pass has smaller
    Bought a three core all aluminum radiator same set up except driver fittings are same size so my factory hose doesn’t fit ….. is there an adapter? Or small fitting that enlarges to accommodate the larger hose

    • Marv Beasley  On June 6, 2022 at 6:00 pm

      I would ask your supplier of the all aluminum radiator for a solution. Most times the engine oil cooler in the driver side tank does use larger fittings than the transmission cooler in the passenger side tank so the supplier should have already developed a solution.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: